PerlMagick -- needing to write/read file after every change

PerlMagick is an object-oriented Perl interface to ImageMagick. Use this forum to discuss, make suggestions about, or report bugs concerning PerlMagick.
Post Reply
Posts: 4
Joined: 2012-09-21T11:17:14-07:00
Authentication code: 67789

PerlMagick -- needing to write/read file after every change

Post by jta2012 »

Hi all,

While working with a PerlMagick image, I find myself needing to write the entire file to disk & then re-read it in order to "commit" incremental changes. Please would you review what I'm doing and advise...

My thumbnail approach starts by converting the source image to sRGB:

Code: Select all

$im->Read( 'test.jpg' );
$im->Set( 'colorspace' => 'sRGB' );
$im->Profile( 'sRGB_IEC61966-2-1_black_scaled.icc' );
Then I write & re-read this intermediate sRGB image:

Code: Select all

$im->Write( 'intermediate.jpg' );
$im = undef();
$im = Image::Magick->new;
$im->Read( 'intermediate.jpg' );
Then, using that intermediate sRGB image, I create all thumbnails:

Code: Select all

$im->Thumbnail( '500x500' );
$im->Write( 'thumb.jpg' );
Shouldn't I be able to eliminate that middle step? When I do, however, the resulting thumbnails are different:

1000px with intermediate rewrite, 263,506 bytes:

1000px without, 262,934 bytes:

My photographer customers prefer the thumbs with the intermediate rewrite. There *is* a difference at the byte level (I'm personally not good at comparing almost-identical thumbs so I try to just do whatever my customers prefer).

Is there some PerlMagick function like $im->CommitChangesSoFar() which would let me achieve my middle step without disk activity? Currently the rewrite take 37% of my overall time (1.804 sec total with the rewrite, 1.131 sec without). Or could some IM expert assure me that both sets of thumbs, while binary different, are essentially the same?


I'm using ImageMagick 6.7.9-2 2012-08-25 Q16 on Win2003. My images & scripts are at Here is my exact Perl code:

Code: Select all

use strict;
use Image::Magick;
use Time::HiRes;
my $t;
my $s = [Time::HiRes::gettimeofday()];

my $b_commit_to_disk_midway = 1;

my $temp_file = 'temp.jpg';

my $MAX = 10;

for (1..$MAX) {

	$t = [Time::HiRes::gettimeofday()];

	my $im = Image::Magick->new;
	&report( "start test $_" );

	$im->Read( 'test.jpg' );
	&report( 'initial read' );

	$im->Set( 'colorspace' => 'sRGB' );
	&report( 'set sRGB' );

	$im->Profile( 'sRGB_IEC61966-2-1_black_scaled.icc' );
	&report( 'set ICC' );

	if ($b_commit_to_disk_midway) {

		unlink( $temp_file );

		$im->Write( $temp_file );
		&report( 'wrote temp' );

		$im = undef();
		$im = Image::Magick->new;

		$im->Read( $temp_file );
		&report( 'read temp' );


	foreach my $px (1000, 500, 100) {

		my $size = $px . 'x' . $px;
		my $file = "$size.$b_commit_to_disk_midway.jpg";

		my $clone = $im->Clone();

		$clone->Thumbnail( $size );
		&report( "created thumb $size" );

		unlink( $file );
		$clone->Write( $file );
		my $bytes = -s $file || -1;
		&report( "wrote thumb $size bytes $bytes" );

	&report( "done with $_\n" );

printf( "Overall %.3f seconds per job\n", Time::HiRes::tv_interval( $s ) / $MAX );

sub report {
	printf( "%.3f ms $_[0]\n", Time::HiRes::tv_interval( $t ) );
Posts: 6
Joined: 2012-08-14T15:56:50-07:00
Authentication code: 67789

Re: PerlMagick -- needing to write/read file after every cha

Post by jta2010 »

I eventually found PerlMagick code to do what I needed. To simulate writing & re-reading everything from disk, I use:

Code: Select all

$p_sRGB = Image::Magick->new;
$p_sRGB->BlobToImage( $image->ImageToBlob() );
Calling ImageToBlob() then BlobToImage() will do an in-memory "flush" of the image data.

In my particular case, this did not get rid of the performance hit, but at least it allowed me to see that the duration spent in those steps was on CPU activity and not disk activity.
Post Reply